水冷初體驗..7900GTX+Thermaltake CL-W0052
..剛學會貼圖..貼的不好請見諒耶..:lol ..水冷初體驗..7900GTX+Thermaltake CL-W0052 ..;P.. ..使用平台 :
CPU:E6700 7X495 3.46MHz
記憶體:黑金剛 D9GMH 5.5.5.15 800@990 1GX2
主機板:技嘉 DQ6 P35
顯示卡:微星 7900GTX GPUoc760 記憶體oc900x2
3DMark 2001:1024X768 53056
3DMark 2003:1024X768 29593
3DMark 2005:1024X768 13358
3DMark 2006:1280X1024 7510
]https://i183.photobucket.com/albums/x269/sys510825/GPU.jpg
GPU水冷頭
]https://i183.photobucket.com/albums/x269/sys510825/GPU-1.jpg
GPU正面拋光打磨
]https://i183.photobucket.com/albums/x269/sys510825/GPU-2.jpg
GPU背面拋光打磨
]https://i183.photobucket.com/albums/x269/sys510825/6600GTGPU.jpg
6600GT散熱器..用來取代原本GPU水冷頭加壓固定座..並且多個保險..萬一水冷出狀況..還有氣冷頂著先
]https://i183.photobucket.com/albums/x269/sys510825/.jpg
背面拋光打磨
]https://i183.photobucket.com/albums/x269/sys510825/-1.jpg
原本用來加壓固定水冷頭的兩根小鐵片..XD
]https://i183.photobucket.com/albums/x269/sys510825/7900GTX.jpg
7900GTX剝光照
]https://i183.photobucket.com/albums/x269/sys510825/-2.jpg
順便修正原本斜斜的電源晶體散熱片
]https://i183.photobucket.com/albums/x269/sys510825/3M.jpg
比較低的晶體用厚的3M導熱片貼上..較高的晶體直接上散熱膏
]https://i183.photobucket.com/albums/x269/sys510825/-3.jpg
..這樣就平平的啦..搞定..
]https://i183.photobucket.com/albums/x269/sys510825/1.jpg
完成圖 1
]https://i183.photobucket.com/albums/x269/sys510825/2.jpg
完成圖 2
]https://i183.photobucket.com/albums/x269/sys510825/1-1.jpg
上機圖 1
]https://i183.photobucket.com/albums/x269/sys510825/2-1.jpg
上機圖 2
]https://i183.photobucket.com/albums/x269/sys510825/ThermaltakeCL-W0052.jpg
Thermaltake CL-W0052 水冷模組本體
]https://i183.photobucket.com/albums/x269/sys510825/1-2.jpg
上機夜光照 1
]https://i183.photobucket.com/albums/x269/sys510825/2-2.jpg
上機夜光照 2
]https://i183.photobucket.com/albums/x269/sys510825/EVEREST30NV3826.jpg
待機溫度EVEREST中顯示約30度..NV程式中顯示約38度..測試時室溫約26度..風扇靜音模式
]https://i183.photobucket.com/albums/x269/sys510825/3DMark200153056.NV.jpg
3DMark2001...53056..溫度變化請參考NV溫度程式曲線圖
]https://i183.photobucket.com/albums/x269/sys510825/3DMark200329593.NV.jpg
3DMark2003...29593..溫度變化請參考NV溫度程式曲線圖
]https://i183.photobucket.com/albums/x269/sys510825/3DMark200513358.NV.jpg
3DMark2005...13358..溫度請變化參考NV溫度程式曲線圖
]https://i183.photobucket.com/albums/x269/sys510825/3DMark20067510.NV.jpg
3DMark2006...7510..溫度變化請參考NV溫度程式曲線圖
]https://i183.photobucket.com/albums/x269/sys510825/3DMark2001.jpg
3DMark2001..使用原廠散熱器參考圖片
]https://i183.photobucket.com/albums/x269/sys510825/3DMark2006.jpg
3DMark2006..使用原廠散熱器參考圖片
..完成..感謝賞圖..:Q.. ..
不錯喔,改裝的很好。 改的不錯..
相當用心 一看就知道..
但水管有點太長了吧 原帖由 XF-Team 於 2007-7-29 16:58 發表
改的不錯..
相當用心 一看就知道..
但水管有點太長了吧
..水管接很長..是為了方便測試啦..:lol ..後續跟CPU水冷散熱整合就不會了..:Q.. .. 改得真棒~~~
不知道 風+水冷 跟單獨的風冷 水冷的差異性是多少? 原帖由 msokpee 於 2007-8-1 23:53 發表
改得真棒~~~
不知道 風+水冷 跟單獨的風冷 水冷的差異性是多少?
..風+水冷..呵呵..那個6600GT散熱器上的風扇..使用溫度控制..要65度才會起動..;P.. ..所以測試出來的成績..風扇並沒有在運作..初玩水冷..順便做個保險..以防被我超掛了..:hug:.. ..會用6600GT的散熱器當水冷頭的固定座..是因為原廠的兩根小鐵片太鳥了..:@.... ..風冷 水冷的差異性..參考文章最後測試..即可瞭解..:Q.. .. 看來花了一番功夫~
辛苦了!
頁:
[1]