第一次的水冷改裝MOD硬體開箱+改裝過程日誌(作品完成12/12更新)
各位好,我是AKMod關注水冷改裝已經3.4年了.只是一直沒有身體力行!!
最近剛好幫女友新組電腦所以就先拿來練習練習一下.為自己的水冷組裝熱身
也認識了很多改裝水冷高手
很多問題都有地方詢問跟指導
發自內心感謝各位....
手機拍照畫質不好請見諒很混
剛好參加XF的水冷改裝體驗營
這次選用的是Barrow 的水冷設備
有心想要接觸水冷的玩家真的可以來上課
從水冷硬體各部位的詳細介紹認識到親自施工
真的讓你有完全了解水冷知識的認知
也對後續自己改裝的過程會很有幫助
一開始先把所有水冷改裝套件上機確認位子
接頭部分每個環節都需要確實鎖緊還有O環一定不要忘記!!!
https://www.xfastest.com/data/attachment/album/201611/30/181150ljwmwqtfwhxrkjvv.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181150ayokpvz6339z1viq.jpg
再來開始彎管測量
這邊就真的很花時間了.也因為第一次施工所以彎壞了2根PETG管子
特別是倒角的部分真的要確實修好.不然管子一塞進接頭很容易就把內O環刺破了
久了就會有漏水或是壓力過大噴管疑慮
圖3因為之後考慮到卸水清潔方面所以裝了一個卸水閥方便之後卸水
https://www.xfastest.com/data/attachment/album/201611/30/181152kkmuqhr7ibzg6rpg.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181151qz5stmy8h8yb8tsa.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181151f3313rlj0b80hjhh.jpg
上水後測試沒有任何漏水現象
完工後真心覺得很累人.專注力要很集中
有了這次經驗相信自己的水冷改裝應該會上手許多!!
分享上水完工後的PC
https://www.xfastest.com/data/attachment/album/201611/30/181202st9593w3ffwee66w.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181203antstlw3qwhwszev.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181205ykssxfhk1ajfikti.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181203q4opw2ek2p0e74ee.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181204kdi7i4nusiihwfnj.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181205c2mpizhp3nqwlyr2.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181206qb1pmjmojsxtz170.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181204sgvuh7fzx2qxssxg.jpg
PC硬體
CPU:Intel i7-6800k
MB:ROG STRIX X99 GAMING
RAM:Corsair Dominator Platiunm 32G
GPU:ROG STRIX-GTX1070-O8G
SSD:Intel 600P 256G
HDD:WD 500G
POWER:Corsair RM750X
CASE:Corsair Air 540
水冷硬體
Barrow CPU冷頭-LTYK2-03
Barrow 240冷排-Doubel-S 240
Barrow 16mm硬管接頭-FBYKN-T16 V1
Barrow 上蓋水箱-PBTT-BBB3150
Barrow 馬達套件-DCHL-V2
Barrow 阻水接頭-TLCDT-V1
Barrow 四通接頭-TX4T-A01
Barrow 排氣接頭-TPQZ-V2
Barrow PETG管子-PG1612-L
曜越 C1000 Opaque彩繪水冷液(紅)
DDC馬達
-----------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------
再來自己的水冷改裝已經在準備中.過程再慢慢上傳.目前水冷設備已經訂購等陸續到貨後就會開始建構
先分享一下caselabs SMA8 機殼開箱跟少部分硬體(硬體部分很多開箱文了就不再拍照了@@)
送來時超大一箱
https://www.xfastest.com/data/attachment/album/201611/30/181152j4oypvdpodedoedo.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181153e6tnrq2zjyr67hrj.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181153wzbnj2xdcakr5xgk.jpg
安裝說明書內頁很詳細照步驟就可以自行安裝完成
https://www.xfastest.com/data/attachment/album/201611/30/181154yt7bk74488fs86bu.jpg
先把所有配件拿出來分類擺好.真的超多零件.然後不得不說這家公司商品包裝真的做的太優了
每件商品完全獨立的包裝
https://www.xfastest.com/data/attachment/album/201611/30/181154exlt2wlj6q3zuzx0.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181155eh2a1ezag234yoi4.jpg
螺絲.其他相關組裝的工具跟配件上面都有標籤標示非常棒
https://www.xfastest.com/data/attachment/album/201611/30/181155nrq8ztuaadhtrvvu.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181156niu4jiyv4b4zppyf.jpg
因為配置的螺絲都是十字的所以又去了對岸買了一堆內六腳圓頭.平頭.菇頭螺絲把整台螺絲都換過了
螺絲絕大部分都是6-32粗紋型號跟少部分M3型號
https://www.xfastest.com/data/attachment/album/201611/30/181201yy0k9efffx5x0f7z.jpg
USB3.0 I/O3.5這部分是選購的然後可以選顏色跟機殼同步上漆
Silverstone USB 3.0 I/O 3.5'' bay device (FP32-E)
https://www.xfastest.com/data/attachment/album/201611/30/181200c2kkt94c1f3qn9cj.jpg
開始組裝.....
https://www.xfastest.com/data/attachment/album/201611/30/181156ehhksjjpbrpcsgxg.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181157auifff3hmvjvifjc.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181157qkl1ql57u722k1qq.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181158s9x2cxzu79tz1xxm.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181158gbodwtftvizqf6qq.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181200pf0iyp4zhnniv9i7.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181159hdaiqripe9ddpv9v.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181159mvhbd7u4xzx1slfp.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181202sziaxacxgglsxv42.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181201dujprgm4f2pjnffp.jpg
部分硬體
https://www.xfastest.com/data/attachment/album/201611/30/181206vr32mvucww2e8273.jpg
第一批水冷硬體到貨.簡單開箱一下.後續等其他水冷硬體到貨就會開始組裝
https://www.xfastest.com/data/attachment/album/201611/30/181209jnonvyy7nnmn2rn2.jpg
水冷頭EK-Supremacy EVO-Acetal+Nickel
選用這款是有鍍鎳的..內容物有導熱膏.扣具螺絲.通用背板
非常詳細的說明書只是沒有中文版本.
因為整體想呈現的方式所以選擇黑色頂蓋的商品只有這款可以挑不然本來想上全銅鍍鎳版本的!
CPU接觸鏡面處理相當漂亮.正面有標示進出水孔位安裝時需要注意一下
https://www.xfastest.com/data/attachment/album/201611/30/181219o2hs43nvhjswbh3s.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181213jhh7mvmvfkazuvqh.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181217fim71nhmubn7tb67.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181215aas9yfpi9y6ye9af.jpg
VGA冷頭EK-FC1080 GTX-Acetal+Nickel
一樣選擇鍍鎳全黑版本..內附的說明書照步驟安裝對第一次新手來說不會太困難這方面真的不錯
正面跟背面都有打上FC1080 GTX字樣質感不錯
出水孔因為打算使用管子相接所以就沒有在選購一體式的接頭
https://www.xfastest.com/data/attachment/album/201611/30/181221f2lwu11lwnmvz11u.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181223x52urau9saram5eg.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181225nvugddadodakvbak.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181227oo5lezmqniiofitw.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181229rl2afii0e0d6uddp.jpg
VGA背板EK-FC1080 GTX Backplate-Black
選用同色系黑色....有鍍鎳版本很有鏡面效果
背板正面一樣有1080字樣.導熱膠條需要自己剪裁大小貼上
https://www.xfastest.com/data/attachment/album/201611/30/181231mxoppp5hiyh1qoqb.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181233t27dngp1djavkkrd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181235jdah2su9n4ad4d6v.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181237sllsood3sb3q4u5p.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181239jfzh30e3ej3qli4f.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181241fzbfblteepil22pb.jpg
D5水泵EK-XRES 100 Revo D5 PWM(incl.pump)
選擇水箱跟水泵組合的.水箱因為還有選購204mm的所以就選擇最便宜款式
以前的版本D5上蓋是正方型的之後改版成為現在這樣圓形然後進出水孔有直切處理
改成圓形好像是要讓玩家更多元更方便安裝比較沒有角度上的限制
不然正方型只能選3個正面安裝
安裝底座有膠條固定非常緊應該是防止馬達震動用的.有多附一個內圈比較不一樣
內容物還有順水接頭.濾水海綿過濾雜質.安裝到機殼用的鑽孔貼紙相當用心
https://www.xfastest.com/data/attachment/album/201611/30/181243vl4holehhr9lro9h.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181245pfy0b4ro0oof4rfo.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181248edtg88hzby3ue4ip.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181252vg0imymzwyr2bsgi.jpg
水箱+上蓋EK-RES X3-TUBE 250(204mm)+EK-RES X3-Multiport TOP
因為機殼可以裝比較大的水箱所以選購204mm的水箱替換上去
上蓋本來附的是單孔.規劃上比較不方便所以加購了3孔的上蓋比較靈活安裝水路
上蓋裡面也是有O環.安裝的時候要認真檢查一下有沒有套上去才不會有漏水疑慮
包裝也是不馬虎.泡泡墊是像袋子一樣的不是一張捲起來的
https://www.xfastest.com/data/attachment/album/201611/30/181255e61m8ahh66gjre6b.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181257llcm4oaujsnluz4c.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181259qan3dun13awz9o5w.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181303r2hco3ltfwyof69p.jpg
冷排EK-CoolStream CE 560(Quad)
560冷排真的相當的大.真是長眼了哈哈~~
140mm只有CE系列可以選可裝4顆14cm的風扇.冷排厚度45mm
進出水孔只有2個旁邊有鑲崁EK LOGO另一頭有刻上型號
跟一般其他品牌冷排比較不一樣的地方是它外邊有包裝起來所以像裝在箱子裡面
大部分都是一體式成型的
安裝螺絲方面內容物附有2組規格6#-32長短螺絲可以安裝
這是要安裝在機殼下方的側排.其他還有280跟480冷排目前還沒有到貨
只是目前規劃上可能會有變動所以打算先把這冷排賣出選購其他冷排https://www.xfastest.com/data/attachment/album/201611/30/181305hjo6tp6ap97uhjat.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181308fxvwj1cgse8gvgbx.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181314jvj8i91xm88xggzi.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181310hw0lpn8kpbsroabf.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181312qw5w6n46tpsn4osd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181319s7sj72rcc3a732y2.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181316c4vthgsxeaaxwexr.jpg
水冷液EK-Ekoolant EVO CLEAR(premix 1L)
它有分預混好跟濃縮的.我買的是預混1L裝的
還有濃縮的需要自己搭配純水混合比例
有多種顏色可以選擇我是選透明的
https://www.xfastest.com/data/attachment/album/201611/30/181211i4lb5w6xlozqx3mh.jpg
目前這批水冷到貨開箱到此..又要漫長等待下一批的到來....
題外話:這批EK商品除了冷排外.其他商品都會有塑膠套包裝然後都會黏上防拆封貼紙.
確保自己買到的都是新品~~這點還蠻保障消費者的......
https://www.xfastest.com/data/attachment/album/201611/30/181323qzigmggfgwac9mgg.jpg
介紹一個好物Dominator Platinum Light Bar的替代品
因為本身規劃上會把Light Bar磨砂噴漆用海盜船正品好像浪費了一點
所以到了對岸看到一組替代品價錢可以省了3分之1以上....磨砂噴漆的過程應該比較不會心痛冷
有3種顏色可以選紅色.綠色.跟這個銀色
https://www.xfastest.com/data/attachment/album/201611/30/181328nd0r32d3r0d8g3du.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181331wmo0phntpmer2ezp.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181333z1xzholaqwjpdkts.jpg
漫長的等待今天到了第二批水冷硬體..因為有商品一直缺貨所以延宕了快10天才下訂單..
目前這批硬體到貨後剩下最後一批BP接頭跟風扇就可以開始動工了
簡單介紹這次的商品
DHL快遞三角箱~因為有訂購PETG100cm的長度所以用這種箱子打包還蠻特別的
https://www.xfastest.com/data/attachment/album/201611/30/181343bl9mpkpnnfln9htx.jpg
primochill這品牌對台灣來說比較陌生但是已經在水冷改裝界讓很多高手使用他們家的產品.
代表品質應該有一定的水準.另外因為很喜歡他們的外觀所以這次選用了他們家的Fitting
因為喜歡比較有厚度的接頭.但是又想要有銷斜角
BP方面比較薄但是有斜角 EK的接頭有厚度但是是平面的哈哈所以訂了這款.
剛好2種喜歡的模式都有結合於一身
這次選消光黑色.他們產品顏色種類真的很多
包裝上一樣很有質感.內有備用O環跟鎖緊接頭的工具.
因為O環也是特規所以一起訂購了一些到時候可以清潔時方便更換.
還有一個專為EK-VGA冷頭進出水接口的O環可以讓接頭本身可以墊高
不至於讓鎖進去的螺紋擋到進出水口有想要添購這接頭的話建議一定要購買
REVOLVER SX 跟一般我們常見的12~16外徑比較不一樣它是英吋的1/2in只有一種尺寸
https://www.xfastest.com/data/attachment/album/201611/30/181345fnaf6gioafr0o947.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181345f0qvybo70373d7y3.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181346n6cmj9ffqge5yb7l.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181346qw4mctge4kmee2tg.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181149sqrkhzxk3w6m2k3n.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181149rd3vjmvdm5xljvlv.jpg
PETG管子怕其他品牌不合所以也一起訂購.大概是介於12~14之間約是12.8mm
因為聽很多高手說12的管子會很難彎所以對自己第一次沒有啥信心
買了100cm 12隻包裝的.....希望不要不夠用
https://www.xfastest.com/data/attachment/album/201611/30/181343h0mln45m5omhe3lr.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181344j395cgjvgcyxf3gw.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181344dt2rr1esjaparrjt.jpg
剛好他們有出專門給電鑽使用的倒角器..所以就順便帶一個回來看看這神奇的東西
但是是特規的應該只能用在1/2in管子上
https://www.xfastest.com/data/attachment/album/201611/30/181347j4ttx3y20rttu0tz.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181347udh5lhj4avywhvvw.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181348iwyyggycj2tr9zpt.jpg
水箱架...
小弟在網路看了幾年水冷改裝..真心很佩服singularitycomputers他們改裝電腦的那種態度..
所有的細節都不馬虎.連要寄送的木板防撞外箱都自己裁切自己做
讓我有努力要向他們學習的目標前進...
這水箱架算是第3代了有一直再做修改..看了真的很喜歡也因為這樣商品一直缺貨所以拖了10幾天才下訂單...
收到商品後真的覺得質感超優.鋁製合金外加陽極處理有多種顏色可以選
還有雙水箱模式..通用12.14CM的冷排鎖
只是真心覺得價錢有夠高的=.=
https://www.xfastest.com/data/attachment/album/201611/30/181348al4uheb4gfc4bf4z.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181349kh7678lii5kfhmkk.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181349k80ad800ar3d8i8o.jpg
這次開箱到這....再來就等最後一批硬體到貨就可以動工了0.0
風扇到貨簡單開箱
本來想用TT風扇..
後來想一想~~想要延用SP120...噴漆
最後看到ML pro 就下訂了
還是受不了Corsair的誘惑
水冷主機風扇的開銷真的也是一大筆~~~痛阿
這款ML PRO 只有單包裝.我是選無光的版本
上一代SP是可以換中間一圈~~這代改成可以換4個角落的防震膠殼
也是有紅白藍.只是需要另外購買
這次使用磁懸技術可以加強靜音
最高可以到2400RPM
風扇本體相當重...我拿起來嚇一跳相當扎實
質感真的很好
https://www.xfastest.com/data/attachment/album/201611/30/181351hnzwjyswlf44f1px.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181350oyyj0wr0c70zwy3m.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181351dd1ozgll6ml8gxgs.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181352v2lsuurs0h7ilhws.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181350beubh7dv668avup7.jpg
冷排EK-CoolStream SE 480(Slim Quad)
選用SE26mm薄排用在機殼上方所以不能太厚加上風扇大概是50mm
本想選用PE系列是雙鰭片設計但是會擋到水路所以做罷
https://www.xfastest.com/data/attachment/album/201611/30/181355tvxqkv6aafheeosa.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181355c27y1r32jqkt6rhk.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181356sie3evf0v6hez4mm.jpg
接頭Bitspower
這次選用CB系列顏色是Carbon Black的外觀跟MB型號Matt Black差在沒有光澤
水路設計上會有90度.45度跟30度接頭
還有一個雙通接頭跟2個卸水閥
因會穿過隔板所以有訂購2個注水座方便銜接
https://www.xfastest.com/data/attachment/album/201611/30/181357xhh8c9okl5iiz95t.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181357f9mmzzo6b71p7fmo.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181357q7czw11w7kwu7vrw.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181358ra2ajhdoz5zi3dhi.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181358cggzgddhjdb7a79f.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181358plf1zxqhvqf4x1ff.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181358w13sigkf6rltglel.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181359qrba66ssalwkkdxd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181359whvqe33327req72v.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181400y02qzqzb11ls28q1.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181400xk353za8kkkaka5v.jpg
亂訂購一些小雜物= =
清潔組Mayhems Blitz Kit
英國水冷液品牌清潔水冷系統雙劑組合
第一劑是清潔冷排的去銅鏽跟附在鰭片上的雜質.需要用浸泡的方式大概12小時
第二劑是清潔水路的.放水後直接加入運作12小時後再用純水清洗跑2.3次就可以完成
(一.二劑都需要加純水稀釋)
https://www.xfastest.com/data/attachment/album/201611/30/181353ey11xngey0axghrx.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181353bo83z3gesmhu7es2.jpg
預跑系統清潔跟水冷液稀釋保護
PrimoChill SysPrep
PrimoChill Liquid Utopia
左邊這是在你完成水冷管路完成時要注水之前先用這個預跑12小時清潔所有的水冷硬體內雜質
一樣曜加純水比例稀釋
右邊是當你只想用純水當水冷液的時候.因為還是會有雜質這可以跟純水稀釋過後保護水路
防藻類跟有機物腐蝕
https://www.xfastest.com/data/attachment/album/201611/30/181352s19o19czw114mm9b.jpg
濾網demcifilter
這家公司在南非~專門製作各家品牌各型號的所有防塵濾網.幾乎都是對應個別型號機殼來製做的
非常合用!!是磁性雙面可拆的一面黏在機殼上另一面磁吸上去可以拆下直接水洗
https://www.xfastest.com/data/attachment/album/201611/30/181354pm0n39kzlqbx3mdn.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181354sjh0n70ck9ic0iqn.jpg
感謝各位傷眼觀看
終於可以動工了下禮拜開始組裝....
忙了快2個禮拜才把主機大致上改完95%了...
目前還會有小修改大概要在1個禮拜才會100%完成作品
以下就是大概的改裝過程圖片跟小小解說
冷排清潔
冷排雖然是全新的但是看了很多改裝視頻其實裡面是很髒的!!很多細小的雜質~
所以要上水路前建議真的需要清潔一下
我是用純水加入8分滿後鎖上堵頭開始用盡洪荒之力上下左右的搖反覆大概4.5次才終於沒有雜質....真的累人只是為了後續使用長久.前製作業真的不能少
https://www.xfastest.com/data/attachment/album/201611/30/181401ynlz202n2ols2900.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181401x41xx60poxah6zhp.jpg
上CPU水冷頭
先驗明一下正身~~
https://www.xfastest.com/data/attachment/album/201611/30/181425y5izffrh84rtih8b.jpg
EK-CPU水冷頭有分3種水道所以要看你是甚麼腳位的CPU需要自行更換裡面的墊片
說明書上面會有詳細說明各型號對應的墊片.對第一次裝水冷的我來說還不會算太難
只是微水道鍍鎳那塊需要記一下位子別亂轉裝反了~~
然後上蓋部分有進出水的標示所以可以注意一下自己規劃的水路來轉到需要的位子在上到CPU
2011腳位的不用背板直接鎖上即可
https://www.xfastest.com/data/attachment/album/201611/30/181402md96suc996279789.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181402yvp9ckxhmbpbvdc3.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181403e63b7d130u37q7a0.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181403wmjj40kkx4m0jk64.jpg
EK-GPU水冷頭
一樣體檢一下
https://www.xfastest.com/data/attachment/album/201611/30/181404xdywcf88gmwfjj9w.jpg
顯卡的部分花了我不少時間研究哈哈
拆下原廠散熱上蓋後需要仔細的清潔晶片上殘留的散熱膏
第一次裝真的需要注意的地方還蠻多的怕螺絲沒鎖好.因為有多加背板所以需要注意哪些螺絲不用鎖哪些要鎖在背板
也怕矽膠墊片沒貼好.晶片旁的墊片都有做預切處理所以直接撕下就可以貼上了
對第一次裝的朋友們真的需要反覆的檢查說明書....
https://www.xfastest.com/data/attachment/album/201611/30/181404xy7sxjy3esezqsyz.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181405nxtct10cc02qtkj0.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181405jbrcvvde5j1rvk88.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181405akjz2wvykxcqqk5v.jpg
接頭+水箱+冷排
冷頭都上好後就是開始規劃接頭部分怎麼組成還要邊想水路管子怎麼走
所以這方面需要先把所有的接頭先上定位後再慢慢的修改成最後的成品
建議不確定的接頭跟延長可以多訂一些
不然到時後規劃少了1.2樣還要再下訂單等4.5天會有點麻煩
https://www.xfastest.com/data/attachment/album/201611/30/181405ermjzthrvhsvnsk9.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181406ce5tpjo454m4jmj0.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181406okrkjl2r2w8crzbd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181406t3oodk8k73jujd6p.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181406pvtac20784p0yltl.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181407dpryly1pu5d144zh.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181407qn6vr1riprwvvzrw.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181407iqhlklkg4jjqt4kl.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181410lkkjd77vskj9kjd4.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181411p7q7om725hks7207.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181404n0yzb5xtpzefd5c3.jpg
EK冷排的出水頭可以轉下來方便規劃水路.有些太擠的地方差一點點就可以鎖上接頭的話就可以拆下來直接上接頭
https://www.xfastest.com/data/attachment/album/201611/30/181417xxp43ppxp73p5p45.jpg
上機規劃水路
接頭方面都先鎖上後再來就是把顯示卡連結的管子先做出來這邊需要把顯卡裝上主機版確認2張卡之間的間距來製作
https://www.xfastest.com/data/attachment/album/201611/30/181408csv1wsv3v9xw188c.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181409xadq2qf8222wzelc.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181409ghm4u4q4697umnli.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181410c1bp29imcbyspy1z.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181411cm05f99o55smzz1o.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181412pqdoioxxi5186a5z.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181412fawzgw6i4bsgg5xu.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181413fhi2kchqm2cccthi.jpg
規劃好水路確認定位後就開始測量鑽孔因為有水路規劃是要過隔板到下面冷排的
還有水箱的掛置也需要鑽孔測量
這方面花了我不少時間在前置測量上面.想要很精準無誤不歪的情況把設備就定位
買了電鑽跟梯形鑽頭(有分尺寸可以依自己需求購買我是買6~24mm的尺寸)
還有直角水平尺來測量精確度
先在需要鑽孔的地方貼上遮蔽膠帶方便在上面畫線量尺寸
然後先鑽顯卡下方的孔所以裁切了一根管子來畫定位
畫完後先在中心點用細鑽頭稍微鑽一下方便讓梯形鑽頭可以穩固在中心點往下鑽才不會歪掉
https://www.xfastest.com/data/attachment/album/201611/30/181408omix2ecijmj5mjle.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181413yqoofnm60ho0xb26.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181414n84hf7iy9yfy07by.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181414zn1n9oao9n7osmc1.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181415waazz6oeavpsni2c.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181420chb6h9ghgh9ubasb.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181418f6i6kzqhppxii1ka.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181421k722y2cj1ytwj1pa.jpg
鑽完後還是擔心所以用尺測量一下垂直度!!
https://www.xfastest.com/data/attachment/album/201611/30/181415ykwwza459pehvmem.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181416hyt2t880vh3hw80t.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181422oxg1y99h0zhg3m0m.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181418jyyshuhzbqzh3vln.jpg
再來是掛置水箱
先把機殼平躺方便畫線測量.這次買的singularitycomputers有強化背板所以先把水箱就定位後畫背板外框之後再拿背板來畫中間2孔要鑽的洞
然後D5水泵附近因為要過線所以也順便鑽了大一點的洞讓水泵電源跟PWM線穿到機箱後面
這樣看起來比較整潔
鑽好掛置完水箱就繼續鑽另一個要下隔板到冷排的孔位
鑽完所有孔位真的是鬆了一口氣= =累死人了
https://www.xfastest.com/data/attachment/album/201611/30/181417i7mdrtvd0heeh7et.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181419ntd9hzbtgd8gctbg.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181419m7z7prszew5i7lrc.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181420i3afwnzfw11atdkx.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181421is21lq7lo4z32224.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181422kl8rnpltcttk6t44.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181423p4j6wqekkp4epdjf.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181423xdn4yrj47csdr7a4.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181424fs9o4022iz720io5.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181425xb4c1s7bzbvvllr3.jpg
小插曲
剛好在施工的過程中訂了剛發售的rog claymore到貨
https://www.xfastest.com/data/attachment/album/201611/30/181426feb64w146qfw64e8.jpg
彎管
彎管方面這次primochill的管子是1/2英吋約12.7mm的管子.管壁薄的管子比較難施工需要花更多的時間在烘烤軟化上面
整機的水路規劃80%都還蠻簡單的一個彎只有CPU冷頭是2個90度但不是平行的有一個需要45度讓我真的想罵OOXX哈哈
第一根冷頭到冷排比一較短的部分我前前後後彎了第7根才成功一直抓不到正確的角度
第二跟冷頭到水箱的部分有了前面的經驗1根就搞定了...
後來因為改了接頭方向所以又從新彎了1根也是一次OK~~~~~
管壁薄的施工熱風槍需要離的比平常在遠然後轉的速度可以快一點
時間上要烘的比較久稍微熱一點就起泡了這點需要注意
https://www.xfastest.com/data/attachment/album/201611/30/181428arwvlwpce4pnce5y.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181427n26lr01d22md2d8d.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181428s0qc1c6kuf2kh4ll.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181429agcnlef1lrccocl3.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181429noiogzuzqbqneqng.jpg
顯示卡下來隔板的另一端因為會卡到冷排所以用了2個90度接頭來閃過
https://www.xfastest.com/data/attachment/album/201611/30/181430qtj170egb0c8jbhb.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181430mu4gtxxpxg51z2z7.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181431djbxkkogeekfydce.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181432s5a33zizvd35rifr.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181431ye2dbtgesh0trg2x.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181432dwpj8mumwtttobmo.jpg
噴漆
確認所有管子位子都沒有歪掉後就拆下來準備噴漆
之前有稍微構想一下配色所以記憶體散熱上蓋跟管子都會噴上消光黑來呈現作品
顯示卡連結的2根管子配合2個水箱所以沒上漆之後有上粉色系的水冷液應該會不錯
噴漆選用日本的石頭漆Natoco Spray耐高溫顆粒也蠻細的
記憶體上蓋先用1200水砂紙慢慢磨細
管子部分可以直接噴所以要量一下插進接頭的長度用遮蔽膠帶貼住
噴漆方面需要慢慢薄薄的一層一層慢慢上才會漂亮
大概上了8次每次等10分鐘
成品出來後自己還蠻滿意的質感加分不少
https://www.xfastest.com/data/attachment/album/201611/30/181335qoeer6tql3ol10z8.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181337mrb2e7cy6rrlmovc.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181338pv3777vv3xvhr3ll.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181433zen3sexts8otsft2.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181435gqq17a7zgnaaz10a.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181437gej3akvt72l827ku.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181436ywr8rtzxxdc8itrd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181436wq72zc7ma2q9287z.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181437oxiwcelyaydiyh0i.jpg
模組線包網
準備工具需要蠻多的如果自己沒有要常做學習的話可以直接請專業訂製比較划算
需要電源檢測器.壓接鉗.剝線鉗.退PIN器.斜口鉗.打火機.熱縮套.矽膠線18跟24AWG.閃兵繩跟編織網.各PIN鍍金端子.膠殼等......
好像真的有點多= =
風扇部分因為統一用延長線所以都留5cm包網這樣也比較好理線
會裝2條60cm的白光燈條在機殼上下位子.電源線也是閃兵繩包網
顏色方面選用黑色閃兵繩低調到不能再低調
壓接方面因為真的需要時間多學習所以後來交由專業製作支援
之後會慢慢在這方面多下點功夫研究
https://www.xfastest.com/data/attachment/album/201611/30/181342qdp5nbn5ttzn6kqi.jpg
https://www.xfastest.com/data/attachment/album/201611/30/181339pdmpvypxpyy2jgdl.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181340b7v4tunkguccujou.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181340bdbz0hs0f44j74jb.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181341jcvuzm0suwsfvkse.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181341b4bz4ax0044u8b4g.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181342baqg1gi2zf2gz681.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181435m8ggg4gwhe1y1yl8.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181426wmcxxtezq11mcbuy.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181427jjtt3t2h2q0otbgd.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181433eyudz3xc5zc153ax.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181434ery7vmih8vuizrqc.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181434np8tzxmp8lymfrjd.jpg
組裝上水測試
所有東西差不多都完成了開始組裝回去.整體感覺個人覺得還可以黑色有加分效果
之前有介紹PrimoChill SysPrep這是在第一次完成還沒上水冷液前
先用純水1公升預混好後加進水箱讓它跑完整的水路大概12小時放水就清潔完畢了
https://www.xfastest.com/data/attachment/album/201611/30/181438rhvhpjviqmhvlnlm.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181438ay39y9ke9cw5w8nt.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181439uikxxemkqccmb9nr.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181439vzpkrkq357z5prxt.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181440kvwxtkfw6fw8tj6w.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181440mza96ex202ke9d2x.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181441wbdw9m9smbid98a9.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181441ycp3czzy9ch70y7h.jpghttps://www.xfastest.com/data/attachment/album/201611/30/181442lmv1xkvcmcn19mnl.jpg
大致上完成大概95%.這幾天會在小修改一些東西包含2個注水孔位跟引水管(忘記買很冏=.=)
還有華碩確定不會出新款HB的橋接器所以訂購了EVGA SLI HB橋接器回來改裝
這次是小弟第一次完整的水冷改裝.雖然沒有很大的外觀改裝主題.但是每個環節都很用心跟細膩的去完成它
細膩到連機殼所有2.300顆螺絲也去挑選合適的內六角螺絲來上
所花費的時間從規劃選購硬體到施工完成大概有6個月的時間
是真的很熱愛這塊
也謝謝很多前輩在遇到問題時都會幫忙解答跟教導
讓我順利很多完成作品
學習到很多也認識了更多在這塊熱愛的朋友
等整體完成好後會比較專業的拍照到時候再分享給各位
接觸水冷改裝後真心覺得不是只有需要懂得水冷這塊
要學習各方面領域的東西太多了
之後也會一直慢慢研究跟學習...
如果有機會的話再來第2部作品哈哈
剩下5%的完成度想讓改裝更細膩跟完整
所以多了2項最後的修改
第一部分:
為了讓改裝細節更完整買了primochill G1/4螺紋的漏斗
從機殼上部直接注水也方便許多
因有2個水箱所以要讓它單獨注水
於水箱上面的多出接口開始鑽孔至後背版
再往上鑽孔銜接頂部注水座接頭
https://www.xfastest.com/data/attachment/album/201612/11/002353ozme46u9bs0bldb7.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002351vbafcabczjnumcxx.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002309fvoo7kasggm8a7sl.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002310wuwupkuuqu4k3wk6.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002311zson2jh330igji4g.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002312onrg49gtf4xxna4z.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002314sfosf838n9izl8b3.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002315py1z3kicwdw13sj3.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002318unmu60z7aoor0woo.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002319yb97yze9loar7rb1.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002322x4esfeh1cc4fxc48.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002324ni76tmpm7bpjp6p0.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002325aohvouktusdu45hk.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002327hy8ueynf2hwcu0oo.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002330wsyczsys5tgjno8s.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002331mexyoh0xx06pymie.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002334en5eofo0v9mp08en.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002336mgc1bz5666lc84n6.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002338bpd0a00d12gxxk0o.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002339ak7vo9a2h9627f19.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002341rgsgb00wtmsb0gea.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002343nxzg1y4h57mjyhxh.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002345lkkbv5dccwbcdwxq.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002407u4l53f55f23o4lm3.jpg
第二部分:
改裝橋接器跟燈箱
因為ROG沒有出自己的SLI HB BRIDGE
所以自己大概想了一下構想決定自己做做看結果效果還不錯
先把敗家之眼LOGO準備好還有參考了ROG之前3D列印的圖片
先買了其它牌子的新板橋接器分解拆了它哈哈
量好外框尺寸正面線條用雷刻割線
再來內部部分需要塞RGB燈條來接上主機板同步燈光效果
所以厚度需要預留
還需要閃過PCB版上的焊點需要裁切很多小擋片來讓它可以靠在上面
最後還需要鎖螺絲的腳座全部組合黏上就大功告成
做了2種版本一種是RGB燈效的另一種用了鏡面效果不一樣的感覺還不錯
燈箱部分就只是把燈條放進壓克力做成的長條箱子上面白色壓克力會有均光的效果質感有提升哈哈
https://www.xfastest.com/data/attachment/album/201612/11/002310wd6cjt66mcexf6r6.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002347d7bfbdxif9hk9xko.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002349sutgcgpkzg3mjcm5.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002401lemzl98ems89xlbt.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002417jhkpwrtqpjmqr4t6.jpghttps://www.xfastest.com/data/attachment/album/201612/11/004538vr7ebr71hpb3ue2y.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002355jx8tat05r82k0z0e.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002357psw7fqsf09wz6z09.jpg
https://www.xfastest.com/data/attachment/album/201612/11/002405atw3izrzinw8hcnz.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002409c12j4h4j8e70u07c.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002411qntl3nq4d2wbiobo.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002413k59ee9mpmmjo5jqd.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002403cb0bnaqjul7sm2lz.jpg
還有因為風扇包網的緣故所以順便裁切了卡典來填上去不然原本的貼紙已經沒有甚麼黏性
https://www.xfastest.com/data/attachment/album/201612/11/002359quv6zu6ucc596u9t.jpghttps://www.xfastest.com/data/attachment/album/201612/11/002415wwwado29gp0gdhqm.jpg
這次改裝的工具!!
https://www.xfastest.com/data/attachment/album/201612/11/011421e4r4xiwcoz74wxcg.jpghttps://www.xfastest.com/data/attachment/album/201612/11/011422xbbvrizmqbbmukcs.jpghttps://www.xfastest.com/data/attachment/album/201612/11/011422jfwn1og8woo98j0t.jpg
改裝完成作品分享
~Black tone~
Spec:
Intel i7-6950X
Asus Rampage V Edition 10
Corsair Dominator Platinum 32GB 3200MHz
Evga GTX1080 FE SLI
Intel 750
Corsair AX1500i
Corsair ML120PRO ML140PRO
Caselabs SMA8
Custom Cables
Custom ROG SLI HB BRIDGE
Watercooling:
EK-Supremacy EVO-Acetal+Nickel
EK-FC1080 GTX-Acetal+Nickel
EK-FC1080 GTX Backplate-Black
EK-XRES 100 Revo D5 PWM
EK-RES X3-TUBE 250
EK-RES X3-Multiport TOP
EK-CoolStream SE 480
EK-CoolStream CE 560
EK-Ekoolant EVO CLEAR
Bitspower Fittings(Carbon Black)
PrimoChill-Rigid RevolverSX Fittings
PrimoChill-Rigid PETG
PrimoChill-Threaded G1/4 Funnel
SingularityComputers-Ethereal Single(Black)
整機換上各尺寸內六角螺絲
感謝XF提供改裝場地及專業拍攝!
https://www.xfastest.com/data/attachment/album/201612/12/225307gi4p1ki7ld6cilid.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225312r2xl662c8ntwwcgi.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225324v37qy7cykckctn3f.jpg
https://www.xfastest.com/data/attachment/album/201612/12/230220yzl43xzxjhwzl33h.jpg
https://www.xfastest.com/data/attachment/album/201612/12/225400k4lwf0f4f3dl3343.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225415jyozplyy4kznpwwk.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225443p0l1163336s1s1fm.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225452ca87ezaaup8u1070.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225501cluu96k5lll6g569.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225510cd5w29xsxhi29z9s.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225518l826p2pbr6p1h12g.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225526z2uv95wxac5u16vj.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225534n88v9tq8g88vq90e.jpghttps://www.xfastest.com/data/attachment/album/201612/12/225544u6lv63uuppwklu3h.jpg
完成作品照片會放在
https://www.facebook.com/akenmodtw/
之後會陸續更新製作過程...
影片過幾天再發布
感謝各位的鼓勵 工程浩大，超屌!
:victory:... 插最快 發表於 2016-11-30 19:06
工程浩大，超屌!
哈哈真的~~
自己搞一搞感覺好像有點浩過頭了 大工程啊!!:kiss:... wingphoenix 發表於 2016-12-1 23:14
大工程啊!!
哈哈
目前剩下的5%真的是個大工程
要全部卸下硬體
鑽4個洞
頁:
[1]